HS-5084MG Servo


	ServoCity- Servos & Accessories- Hitec Servos- HS-5084MG Servo-


	HS-5084MG Servo

26.39 oz-in.

0.05 sec/60°

Absolutely amazing speed is what the all new HS-5084MG servo is about. The “extreme speed” HS-5084MG Digital Micro Tail Rotor servo is based on the HSG-5083 but utilizes a standard frame rate digital amplifier. Designed to work with most gyros the HS-5084MG is designed to obtain optimum performance in the T-Rex 400-450, Helimax 400-450 or similar class of electric helis. Not only does the all new HS-5084MG give you extreme speed, it also offers excellent centering, resolution and durability for those looking to save weight without sacrificing performance. An absolutely perfect choice for smaller airplanes, heli’s, boats, cars, trucks and robots. Incorporating the standard size Hitec spline means that all of your servo horns from standard size Hitec servos work with the HS-5084MG.
Although the HS-5084MG is digital, it is not programmable..


	*Digital servos do not need to be programmed to operate. They work great right out of the box and purchasing a programmer is not neccessary.

This servo can operate 90° when given a pulse signal ranging from 900usec to 2100usec.

Price:

$57.99

Part:

35084S

Status:

Qty:

Detailed Specifications

Control System: +Pulse Width Control 1500usec Neutral
Required Pulse: 4.8-6.0 Volt Peak to Peak Square Wave
Operating Voltage Range: 4.8-6.0 Volts
Operating Temperature Range: -20 to +60 Degree C (-68F to +140F)
Operating Speed (4.8V): 0.07sec/60° at no load
Operating Speed (6.0V): 0.05sec/60° at no load
Stall Torque (4.8V): 20.83oz/in. (1.5kg.cm)
Stall Torque (6.0V): 26.39oz/in. (1.9kg.cm)
Operating Angle: 45 Deg. one side pulse traveling 600usec
360 Modifiable: Yes
Direction: Clockwise/Pulse Traveling 1500 to 2100usec
Idle Current Drain (4.8V): 3mA at stop
Idle Current Drain (6.0V): 3mA at stop
Current Drain (4.8V): 200mA/idle and 2.0 amps at lock/stall
Current Drain (6.0V): 240mA/idle and 3.0 amps at lock/stall
Dead Band Width: 2usec
Motor Type: Carbon Brush
Potentiometer Drive: 6 Slider Indirect Drive
Bearing Type: Dual Ball Bearing MR106
Gear Type: Metal Gears
Connector Wire Length: 7" (178mm)
Dimensions: 1.14" x 0.51"x 1.18" (29 x 13 x 30mm)
Weight: .76oz (21.7g)



	Included servo mounts


		Standard size servo spline





		Included servo horns and hardware


	A = .51” (12.9mm) B = .402” (10.2mm) C = .976” (24.8mm) E = .264” (6.7mm) F = .872” (22.15mm) G = .409” (10.4mm) H = .772” (19.6mm) J = 1.565” (39.75mm) K = .390” (9.9mm) L = .179” (4.55mm) M = 1.136” (28.85mm) X = .140” (3.56mm)


	Copyright 1999-2009 Robotzone. LLC. - All Rights Reserved ServoCity is a registered trademark of Robotzone, LLC.