HS-5085MG Servo


	ServoCity- Servos & Accessories- Hitec Servos- HS-5085MG Servo-


	HS-5085MG Servo

59.7 oz-in.

0.13 sec/60°

Nearly 60 in-oz. of torque in a micro servo is amazing! Not only does the all new HS-5085MG give you power, it also offers excellent centering, resolution and durability for those looking to save weight without sacrificing performance. An absolutely perfect choice for smaller airplanes, heli’s, boats, cars, trucks and robots, the HS-5085MG offers a fine balance between speed and torque. Incorporating the standard size Hitec spline means that all of your servo horns from standard size Hitec servos work with the HS-5085MG. We offer the new HS-5085MG servo in several configurations, 90° stock rotation, 180° modified rotation (programmed), continuous rotation (potentiometer is left outside the servo case) and reverse rotation.


	*Digital servos do not need to be programmed to operate. They work great right out of the box and purchasing a programmer is not neccessary.



		Programable Features: - Dead Band Width - Direction of Rotation - Speed of Rotation (slower) - End Points (up to 120 degrees) - Neutral Points - Fail Safe On/Off - Fail Safe Points - Resolution (default is set at high) - Overload Protection (default is off)

	Detailed Specifications
	Control System: +Pulse Width Control 1500usec Neutral Required Pulse: 4.8-6.0 Volt Peak to Peak Square Wave Operating Voltage Range: 4.8-6.0 Volts Operating Temperature Range: -20° to +60° C (-4°F to +140°F) Operating Speed (4.8V): 0.17sec/60° at no load Operating Speed (6.0V): 0.13sec/60° at no load Stall Torque (4.8V): 50oz/in. (3.6kg.cm) Stall Torque (6.0V): 59.7oz/in. (4.3kg.cm) Operating Angle: 45 Deg. one side pulse traveling 400usec 360 Modifiable: Yes Direction: Clockwise/Pulse Traveling 1500 to 1900usec Idle Current Drain (4.8V): 3mA at stop Idle Current Drain (6.0V): 3mA at stop Current Drain (4.8V): 200mA/idle and 2.0 amps at lock/stall Current Drain (6.0V): 240mA/idle and 3.0 amps at lock/stall Dead Band Width: 2usec Motor Type: Carbon Brush Potentiometer Drive: 6 Slider Indirect Drive Bearing Type: Dual Ball Bearing MR106 Gear Type: Metal Gears Connector Wire Length: 7" (178mm) Dimensions: 1.14" x 0.51"x 1.18" (29 x 13 x 30mm) Weight: .77oz (21.9g)


	This servo can be configured to operate a maximum of 120°. Option 1, send a pulse signal ranging from 950usec to 2050usec. Option 2, use a Hitec programmer to modify the internal servo program.

Price:

$46.99

Part:

35085S

Status:

Rotation:

Direction:

Qty:



	Included servo mounts



	Standard size servo spline



	Included servo horns and hardware


	A = .51” (12.9mm) B = .402” (10.2mm) C = .976” (24.8mm) E = .264” (6.7mm) F = .872” (22.15mm) G = .409” (10.4mm) H = .772” (19.6mm) J = 1.565” (39.75mm) K = .390” (9.9mm) L = .179” (4.55mm) M = 1.136” (28.85mm) X = .140” (3.56mm)


	Copyright 1999-2010 Robotzone. LLC. - All Rights Reserved ServoCity is a registered trademark of Robotzone, LLC.